B&G_AutoPilot_Drive

AutoPilot Drive Units

HYDRAULIC STEERING:
Boats with hydraulic steering use a reversing pump connected to the existing steering system. Pilot type is determined primarily by the total steering capacity of the existing system.

MECHANICAL STEERING:
Linear drives are used by most sailboats and by powerboats with mechanical steering. The cylinder is generally attached to a separate tiller arm connected to the rudder shaft.

Rotary Rudder Reference Unit

(compatible with Type 0, 1, 2, 3 & 4 Rams / Pumps)

The industry standard in rudder reference sensors.

Robust and proven by round the world sailors.

NEW Linear Feedback Rudder Sensor Unit
(compatible with Type 1 & 2 Rams)

Fits directly on top of the hydraulic ram.
Quick and easy to install.
Occupies less space.
Offers greater pilot control.

To the right a RAM with the Old discontinued Linear feedback unit

Pilot Packages

1. Pilot Base Pack-All packs include ACP (Advance Control Processor, Pilot Display and all hardware for complete install.

Note: The H1000 ACP is compatible with either a Type 1 or Type 2 drive unit.

Note: H1000 and Network pilot packs include fluxgate Compass.

2. Drive System - Each drive pack includes drive unit and hardware for a complete install.

3. Compass options - For H2000 Only

4. Rudder Feedback Options - For limited space RRF-ACP is recommended.

Follow the chart below for recommended drive solutions

DRIVE UNIT & CAPACITY SELECTION GUIDE

BOAT LENGTH

10' 5'

20'

31'

40' 5'

50'

60' 6'

70'

80'

90' 96'

TYPE 0: Up to 12,000 lbs.

TYPE 1: Up to 33,000 lbs.

TYPE 2: Up to 42,000 lbs.

DISPLACEMENT

TYPE 3: Up to 70,000 lbs.

TYPE 4: Up to 110,000 lbs.

PUMP UNIT CAPACITY SELECTION GUIDE

Type 1: PUMP1: 6.1 to 18.3 cubic inches [100-300cc] 12 VDC

Type 2: PUMP2: 16.8 to 30.5 cubic inches [275-500cc] 12 VDC

Type 2: PUMP2: 16.8 to 30.5 cubic inches [275-500cc] 24 VDC

Type 3: PUMP3: 32.0 to 45.8 cubic inches [525-750cc] 24 VDC

The information above is presented as a general guideline for the proper selection of autopilot drive units. The drive unit requirement will determine which Advanced Control Processor (ACP) system is needed to complete the installation. The primary consideration in determining the drive unit type is boat displacement.

In addition to boat size, the proper selection of a hydraulic pump for hydraulic systems will be further defined by the total capacity or displacement of the boat's steering system.

Contact us, Write, Fax, E-Mail,

Call M-F [9.00am-5.00pm Central US (- 6h GMT)] to:
Hellas Marine, Inc.

Chicago Marine Electronics
512 W. BELDEN Avenue #2A
CHICAGO IL. 60614 USA
Phone : +1 (773) 832-0679
Fax : +1 (773) 296-6908
" E-Mail "

Marine Electronics, Navigation & Marine products.

Note: Reproduction and copy of any page, picture, document or material used in the www.HellasMarine.com & www.ChicagoMarineElectronics.com web site for commercial or any other use with out written authorization from Hellas Marine, Inc. & Chicago Marine Electronics is prohibited.
Note: Posted prices do not include TAX for Illinois State residence, S&H, Installation, Training or Calibration of items sold.
Note: Minimum Shipping charge of $ 15.⁰⁰
Note: Products are not returnable, all sales are final, defective products are repaired or replaced by the manufacturer, as per manufacturer warranty.
Note: Our services are a person to person basis, to maintain our good prices and the latest software versions on product sold our stock is low, orders are processed by the date they received. Orders are NOT Billed/Charged until they are shipped.
Note: Prices subject to change with out prior notification. Contact us for details.

Created by Hellas Marine Inc.

www.HellasMarine.com